farefasad.blogg.se - Punto switcher 3.4.0.390

Punto switcher 3.4.0.390 how to#
Punto switcher 3.4.0.390 windows 10#
Punto switcher 3.4.0.390 software#
Punto switcher 3.4.0.390 code#

If there is anything that you would like to add, please leave a comment below. Good luck diagnosing P0121 in your Fiat Punto. It no longer is accurately tracking how hard the fuel pedal is being pushed.ĭiagnosing the issue with a scanner or having a mechanic take a look can save the expense of buying a TPS sensor that your Punto does not actually need. Most of the time, the problem when P0121 is thrown will be the TPS sensor itself.

Punto switcher 3.4.0.390 software#

This free software is an intellectual property of Yandex.

Punto switcher 3.4.0.390 windows 10#

This free PC program was developed to work on Windows 2000, Windows XP, Windows Vista, Windows 7, Windows 8 or Windows 10 and is compatible with 32-bit systems. Punto Switcher lies within Office Tools, more precisely Timekeeping.

Punto switcher 3.4.0.390 code#

If it all checks out and the code comes back, they may go ahead and replace the TPS sensor in question. Download Punto Switcher 4.4.4.489 from our website for free. After that they’ll typically inspect the TPS wiring to make sure that it is not loose or damaged. The mechanic will also compare the data from TPS circuit “A” and “B” to see where the discrepancy is. They’ll then see if the problem comes back. This is what you need to address.Ī good mechanic will utilize a scanner to diagnose when the codes were set and reset them. The computer thinks that the culprit is the “A” circuit. It’s a general powertrain code, which means that it has the same meaning regardless of who manufactured the vehicles (1996+, Punto or not). In normal English, the two TPS circuits can’t agree on how far the gas pedal has been pushed down. P0121 will trigger in your Fiat Punto if it’s TPS A circuit has an output voltage that goes above or below the sensor’s normal operating range.

A discrepancy between the voltage reading from TPS sensor circuit “A” and TPS circuit “B” where TPS circuit “A” is lower than the specified voltage range by more than 0.8 volts.

A discrepancy between the voltage reading from TPS sensor circuit “A” and TPS circuit “B” where TPS circuit “A” is higher than the specified voltage range by more than 1.6 volts.

In the Fiat Punto, the P0121 is going to be caused by:

The vehicle’s ECM will control the amount of fuel entering the engine in order to control engine speed.įailsafe mode leaves a vehicle in a state that makes it almost impossible to drive and enjoy.

However, i could not get a OE switch for the boot door which makes the lamp to turn on when the boot is opened. fitment was easy, the lamp directly fits the slot in the boot as shown in the picture. Since the ECM won’t really know how much throttle response is actually happening when you push the gas. Automatically switches between Russian and English keyboard layouts. Got the OE boot lamp for 295 rupees and got it installed to Punto today. This limited power is a failsafe to keep the vehicle able to move, but not super fast.

The vehicle will hardly respond to the throttle at all.

Here are the most common symptoms of P0121: The symptoms of P0121 are going to vary by year and model, but they certainly are going to cause noticeable changes in the way that your Punto drives. P0121 will trigger in your Fiat Punto if it’s TPS “A” circuit has an output voltage that goes above or below the sensor’s normal operating range.

Punto switcher 3.4.0.390 how to#

There’s a YouTube video below that shows how to go about diagnosis with a scanner. Diagnosing it can be tricky without a good scanner and the knowledge of what you are doing. OBDII code P0121 is a serious problem that requires serious attention. It is relatively serious problem since it can leave your vehicle in failsafe mode. It’s an OBDII code and has to do with the Throttle Pedal Position Sensor. You can also use it to show links above or below your posts, offering them in other languages. WPML lets you add a language switcher in different ways: in a menu, as a widget, or in the site’s footer. I am thinking of taking a fused power feed from the cigarette lighter circuit, and I was going to make my own wiring loom, so I know I'll probably have to solder some wires to the mirror control switch.P0121 is a relatively common trouble code with the Fiat Punto. A language switcher allows visitors to select the language in which they want to read your content. Am I right in thinking the electric Punto mirrors can both be electrically folded back by putting the mirror selector switch in the middle then pressing the direction button?ģ. Am I right in thinking I will need to tap into the heated rear window wiring?Ģ. I understand what has been said at the start of the thread in order to get the mirrors moving, I am just wondering how to get the heated part working. I'd really appreciate some help if someone could enlighten me.ġ. The only thing the mk2 Sporting was missing when it was released, is electric heated mirrors in my opinion. Sorry to jump on an old thread, I've searched for ages trying to get a few answers.